描述

纤维含量为40%的PPS塑料颗粒1

是所有先进工程塑料中最广泛的耐化学品性

改进了PPS的尺寸稳定性和热性能

使强度保持在425ºF以上，酸

最小吸水率

优良的电绝缘体

极低的线性热膨胀系数

含40%纤维的聚苯硫醚塑料颗粒1

产品详细信息

<。电子方面：高压元件、外壳、插座、摄像机接线柱、计算机、电机起动器线圈、叶片、电刷支架和转子绝缘部件、接触开关、继电器、电熨斗、吹风机、灯座、加热器风扇、F级胶片等。

2。汽车工业：适用于废气再循环阀和水泵叶轮，以及蒸发器、排气装置、排气调节阀、光反射器、轴承、传感元件等。

<3。机械行业：用作轴承、泵、阀门、活塞、精密齿轮，以及复印机、相机、计算机零件、管道、喷雾器、喷油器、仪表零件等。

<4。化学工业：用于制造耐酸碱阀门、管道、管件、阀门、垫片和耐腐蚀零件，如潜水泵或叶轮

2。桶温：建议桶温为290～330℃

3。模具温度：建议模具温度为130～150℃

4。注射压力：一般注射压力为30-100MPa。为了防止闪蒸，可以使用较低的喷射压力

5。注射速度：高速注射可获得外观良好的模制产品。然而，很容易导致成品翘曲和烧焦。因此，如果产品外观良好，则不需要高速注射

6。背压：建议背压不超过1.0MPa。当测量不稳定时，应适当增加背压

7。螺杆转速：通常螺杆转速设置为40-100转/分（rpm）。如果螺杆转速高于200转/分钟，很容易导致玻璃纤维断裂并导致树脂升温

请联系我们，了解含40%纤维的PPS塑料颗粒的详细信息

是专业的含40%纤维的聚苯硫醚塑料颗粒制造商之一，您可以从我们工厂以优惠的价格订购含40%纤维的高品质聚苯硫醚塑料颗粒

PPS Plastic Particles With 40% Fiber1

Broadest resistance to chemicals of all advanced engineering plastics
Improved dimensional stability and thermal performance over PPS
Maintains strength above 425º F
Inert to steam, strong bases, fuels, and acids
Minimal water absorption
Excellent electrical insulator
Very low coefficient of linear thermal expansion

PPS Plastic Particles With 40% Fiber1

Product Details

Add carbon fiber 35%PPS/antistatic

PPS plastics are widely used in:

1. Electronic aspect: high-voltage components, housings, sockets, wiring posts of video cameras, computers, motor starter coils, blades, brush brackets and rotor insulation parts, contact switches, relays, electric irons, hair dryers, lamp holders, heaters Fan, F grade film, etc.

2. Automobile industry: suitable for exhaust gas recirculation valves and water pump impellers, as well as vaporizers, exhaust devices, exhaust regulating valves, light reflectors, bearings, sensing components, etc.

3. Machinery industry: used as bearings, pumps, valves, pistons, precision gears, as well as copiers, cameras, computer parts, pipes, sprayers, fuel injectors, instrumentation parts, etc.

4. Chemical industry: used to make acid and alkali resistant valves, pipes, pipe fittings, valves, gaskets and corrosion resistant parts such as submersible pumps or impellers.

Injection molding conditions

1. Pre-drying: drying at a temperature of 120°C to 150°C for 4 to 6 hours.

2. Barrel temperature: The recommended barrel temperature is 290～330℃.

3. Mold temperature: Recommended mold temperature is 130～150℃.

4. Injection pressure: Generally, the injection pressure is 30-100 MPa. In order to prevent flash, a lower injection pressure can be used.

5. Injection speed: High-speed injection can be used to obtain molded products with good appearance. However, it is easy to cause warping and scorching of the finished product. Therefore, if the product has a good appearance, high-speed injection is not required.

6. Back pressure: It is recommended that the back pressure should not exceed 1.0 MPa. When the measurement is unstable, the back pressure should be appropriately increased.

7. Screw speed: Usually the screw speed is set to 40-100 revolutions/min (rpm). If the screw speed is higher than 200 revolutions/min, it is easy to cause the glass fiber to break and cause the resin to heat up.

Contactnowformoredetailsabout PPS plastic particles with 40% fiber.

Kitty Liu< ###>

is one of the professional pps plastic particles with 40% fiber1 manufacturers, you can order high quality pps plastic particles with 40% fiber1 at good price from our factory.