描述

电气和汽车配件用环保尼龙66树脂尼龙66 GF10-50玻璃纤维尼龙颗粒

一,。增强PA66材料

2。用于注射成型

3。机械强度高

4。免费样品

环保型PA66树脂尼龙66 GF10-50玻璃纤维PA颗粒，用于电气和汽车配件

产品详细信息

用于电气和汽车配件的环保型PA66树脂尼龙66 GF10-50玻璃纤维PA颗粒

PA66应用

在大多数应用上与PA6竞争。PA66广泛应用于汽车工业、电器外壳以及要求抗冲击性和强度的场合

PA66注射成型工艺条件

干燥

如果材料在成型前密封，则无需干燥；但是，如果容器保持打开状态，建议在85摄氏度（185华氏度）的热风炉中干燥。如果含水量大于0.2%，建议在105摄氏度（220华氏度）下真空干燥12小时

熔体温度260-290摄氏度（500-554华氏度）；玻璃填充等级为275-280摄氏度（527-536华氏度）；应避免熔体温度超过300摄氏度（572华氏度）

建议模具温度

80摄氏度（176华氏度）。模具温度影响结晶度水平，结晶度水平反过来影响物理性能。对于薄壁零件，如果使用低于40摄氏度（104华氏度）的模具温度，结晶度会随时间变化。在这种情况下，可能需要退火以保持尺寸稳定性

材料注射压力一般在75-125 MPa之间，取决于材料和产品设计

注射速度

高（对于增强等级略低）

是电气和汽车配件制造商的专业环保pa66树脂尼龙66 gf10-50玻璃纤维pa颗粒之一，您可以从我们工厂以优惠的价格订购高质量的环保pa66树脂尼龙66 gf10-50玻璃纤维pa颗粒，用于电气和汽车配件

Environment Protection PA66 Resin Nylon 66 GF10-50 Fiber Glass PA Pellets For Electrical And Auto Accessories

.
1. Reinforced PA66 Material
2. Used for Injection Molding
3. High mechanical strength
4. FREE SAMPLE

Environment Protection PA66 Resin Nylon 66 GF10-50 Fiber Glass PA Pellets For Electrical And Auto Accessories

Product Details

Environment Protection PA66 resin Nylon 66 GF10-50 Fiber Glass PA Pellets for Electrical and auto accessories

PA66 Applications

Competes with PA6 for most applications. PA66 is heavily used in the automotive industry, appliance housings, and generally where impact resistance and strength are required.

PA66 Injection Molding Processing conditions

Drying

Drying is not required if the material is sealed prior to molding; however, if the containers are left open, drying in a hot air oven at 85 C (185 F) is recommended. If the moisture content is > 0.2%, vacuum drying at 105 C (220 F) for 12 hours is recommended.

Melt Temperature 260 – 290 C (500 – 554 F); 275 – 280 C (527 – 536 F) for glass filled grades; melt temperatures above 300 C (572 F) should be avoided

Mold Temperature

80 C (176 F) suggested. Mold temperature affects crystallinity level which in turn affects physical properties. In the case of thin walled parts, crystallinity changes with time if mold temperatures of less than 40 C (104 F) are used. In such cases, annealing may be needed to retain dimensional stability.

Material Injection Pressure

Generally between 75 – 125 MPa, depends on material and product design

Injection Speed

High (slightly lower for reinforced grades)

is one of the professional environment protection pa66 resin nylon 66 gf10-50 fiber glass pa pellets for electrical and auto accessories manufacturers, you can order high quality environment protection pa66 resin nylon 66 gf10-50 fiber glass pa pellets for electrical and auto accessories at good price from our factory.